Familiarize yourself with the AV equipment
Power Supply
The green light (outlined below) indicates that the power supply is turned on.
Main PC
When the PC is on, the light illuminates WHITE, if you find the PC turned off, press the power button once.
Do not shut down the main PC.
When finished, log off of the main PC.
If you think the PC is unresponsive, press and hold the power button for a few seconds to force a shut down, wait a few seconds, and then press the power button once to turn it on.
Video Switcher
The video switcher helps select between multiple incoming video sources.
Identify the correct input number for your device connection and select it by pressing the appropriate button
The active selection is backlit with a red light
Make the correct selection:
#1 - Main PC
#2 - DVD/Blu-ray/Multi-Region player
#3 - Guest HDMI
#4 - Not in use
#5 - Not in use
#6 - Not in use
#7 - Document Camera
#8 - Not in use
Room Audio
Note: Make all audio adjustments on the main PC first.
Click the speaker icon (outlined in red).
Drag the slider on the bar left to turn down and right to turn up the volume (outlined in green).
The computer volume is muted if you see the speaker icon with an “x” next to it (outlined in red/green).
To unmute the computer, click the speaker icon with the “x” that is outlined in green.
Amplifier
Red highlighted button: This button can power on or power off the amplifier. Turn it on for any audio needs.
Green highlighted button: It is the master volume knob and can control all audio output from all sources.
Bass Knob: Leave in middle.
Treble Knob: Leave in middle.
Module Knob: Leave in middle.
Input Knobs: Only turn on the one that is necessary. In this case, everything is on “Input 1”.
Input 1: Everything
Input 2: Not in use (leave off)
Input 3: Not in use (leave off)
Input 4: Not in use (leave off)
Input 5: Not in use (leave off)
Input 6: Not in use (leave off)
Input 7: Not in use (leave off)
Input 8: Not in use (leave off)
Sony DVD / Blu-Ray / Multi-Region
.jpg?version=1&modificationDate=1689182147607&cacheVersion=1&api=v2)
The power button is outlined in red.
The disc eject button is outlined in green.
The disc tray is outlined in gold.
Region Free Blu-ray Region change instructions:
Standard DVD Regions 0-8 (region free-code Free)
These are set to automatic - just insert the disc and press play.
To change regions
Blu-ray Regions are changed manually with remote.
Turn player on and open the tray.
Once the tray is completely open and not moving press a button on the remote to select regions.
Zone A: Press the YELLOW button on the remote control.
Zone B: Press the BLUE button on the remote control.
Zone C: Press the RED button on the remote control.
You can now put your disc in the tray and then close the tray.
Troubleshooting:
If your Disc does not play do the following:
Open the tray again and leave the disc in the tray. Once fully open press the color button to select the region. Then close the tray.
Firmware updates - Firmware updates can be done via the internet. To update players firmware; go to the home menu, then setup menu, and then go to Software update. You must have the player connected to the internet. Click on Update Via Internet and if there is a new firmware the player will automatically update. DO not turn the player off while it is updating.
Document Camera Guide
Projector
Point the remote at the front of the projector.
Turning on the projector: Press “On” once (outlined in red).
Turning off the projector: Press “Off” twice (outlined in green).
Projector Screen
The projector screen is manual and there is a string at the bottom center.
To raise the screen, pull the screen by the string out away from the chalkboard a couple of feet, pull down, and release, allowing the screen to retract.
To lower the screen, pull down on the string and let go near the chalkboard shelf for full extension.
